







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Anaheim, CA: What the Job Actually Costs and How Long It Takes
An iron fence in Anaheim usually runs $3,500 to $9,000, and most residential runs are finished in two to four working days once the material is on site. That covers layout, post setting, panel or picket installation, and finish touch-up on a typical front or side yard. The variables that push a project toward either end are linear footage, gate count, finish type, and how much digging the old fence leaves you with. Call (888) 255-9354 for a free on-site estimate.
How We Build an Iron Fence in Anaheim, Start to Finish

The order of operations matters here because Anaheim properties are tight. Alleys, shared driveways, and zero-lot-line townhomes mean we plan fence access before the first post goes in, not after a crew is stuck on the street.
Stage 1: Site visit and layout (day 1, 1 to 2 hours)
We measure the actual run, mark utility locations through Dig Alert, and confirm where the property line sits relative to the fence. You decide at this stage whether the fence sits on the line or a few inches inside it. Pulling that decision early prevents a neighbor dispute after concrete is poured. On tight Anaheim lots, we also confirm truck and wheelbarrow paths so nobody blocks a shared alley for a full day.
Stage 2: Removal and prep (day 1 to day 2)
If there’s an old wood or chain link fence, we remove it and haul it off. Post holes get dug to depth, and for steel posts on a standard residential run that’s often 24 to 30 inches down, wider at the base and backfilled with concrete. On older Anaheim bungalows near the Colony District, we sometimes find old fence footings, tree roots, or fragments of a previous concrete wall in the same trench. That adds time, and we price it before cutting into anything.
Stage 3: Posts and concrete (day 2)
Posts get set, braced, and left to cure. You choose the post spacing (6-foot and 8-foot bays are standard) and the gate location at this stage. We typically let post concrete set overnight before hanging anything heavy. In summer heat we schedule pours in the morning so the concrete doesn’t flash-dry before it’s finished.
Stage 4: Panels, pickets, and gates (day 3 to day 4)
Panels or pickets go up, gates get hung and adjusted for swing and latch, and every weld or fastener gets checked. This is the stage where a good install shows: level rails, consistent top line, and gates that close without dragging. You walk the run with us here before we call it done.
Stage 5: Finish, touch-up, and walkthrough (final day)
Powder-coat scratches get touched in, gate hardware is lubricated, and we walk the fence with you against the original layout. Anything off gets corrected before we leave. Your 730-Day Done Right Promise is in writing, so if a gate settles or a fastener fails after we’re gone, we come back.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Actually Choose Between
Two main material families cover most Anaheim iron fence jobs, and the choice drives most of the price difference.
- Wrought iron (solid bar): The traditional look with a genuine forged or solid-bar feel and the heaviest weight. It holds up longest in Anaheim’s dry summers, but it costs more, needs re-painting every several years, and is heavy enough that gates need solid hinges and posts. Good for historic-feeling properties near downtown.
- Powder-coated steel ornamental: Most of what gets installed on residential Anaheim properties. Lighter, factory-finished, and much lower maintenance. It’s not a forging, so it’s a formed shape rather than solid bar, but for a front-yard run it looks close and holds finish well in arid conditions.
- Aluminum ornamental iron: The lightest and most rust-resistant of the three. It’s the right call for tight alley access where weight matters and for homeowners who don’t want to repaint. It doesn’t have the same heft as steel, and it can be less forgiving of impact.
- Finishes: Black is the standard and the easiest to touch in. Bronze, rust, and custom colors cost more and often need a longer lead time. In Anaheim’s sun, dark colors get hot on the hand; if you have kids who grab the gate, matte black is still the practical pick.
- Gate automation and access: If you’re adding a rolling or swing gate to alley-load or townhome access, the opener choice matters more than the fence itself. Rolling-code remotes are the default because fixed-code openers get cloned easily, and on a shared Anaheim alley that’s a real security gap.
What an Iron Fence Costs in Anaheim, CA

For a typical residential front or side yard run, plan on $3,500 to $9,000. That’s the working range for most Anaheim properties, and where your job lands depends on these variables.
- Linear footage: The single biggest driver. A 40-foot run and an 80-foot run are different jobs, and the price gaps accordingly.
- Material grade: Powder-coated steel sits at the lower end, solid wrought iron pushes the high end. Aluminum lands between and often feels close to steel on a walking budget.
- Gate count and hardware: One pedestrian gate is routine. Driveway gates, automated openers, and alley-access gates with rolling-code remotes add meaningful cost and time.
- Removal of the existing fence: A clean old fence comes out fast. Buried footings, roots, or an old block wall in the same line add labor.
- Site access: Tight Anaheim lots with no driveway or a shared alley mean more hand-carrying of posts, panels, and concrete bags. That adds time, and we price it upfront.
A written estimate from us is line-item, so you see the posts, panels, gates, removal, and concrete listed separately. What’s typically not included: landscape repair after digging, permits if your Anaheim job requires one, and any additional electrical work for gate automation beyond the opener itself. Our no-hassle upfront pricing means the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Anaheim Homes Specifically Do to an Iron Fence Job
Anaheim isn’t one kind of job. Downtown neighborhoods near the Colony District and the older grid in 92805 are full of early-1900s bungalows and Craftsman homes where fence lines run tight to the house, the alley, and the neighbor. That means more gates, more careful line-marking, and more of what a contractor has to plan before digging. On the east side, 1960s and 70s ranch tract homes in 92806 and Anaheim Hills properties in 92807 come with wider setbacks and longer runs, but Anaheim Hills adds slope and retaining-wall conversations that flatland subdivisions never touch. Santa Ana wind events out of the canyons are part of why we spec heavier posts and hardware on open yards there. And because Anaheim issues its own permits through the city’s building division rather than the county, a fence near a property line or in a setback needs the city’s answer, not a generic rule. ZIPs we work in most here include 92806, 92816, 92817, and 92899, plus the surrounding Anaheim service area.
If the fence is part of a larger yard project, homeowners often pair this with Patios, Walkways & Pool Decks in Anaheim so the hardscape and fence line are planned together. If a same-line block wall is coming down for a new gate, that’s usually part of a full Fence Installation in Anaheim plan.
Serving Anaheim, CA – Our Local Coverage Area
We serve Anaheim and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Anaheim

Most residential runs are done in two to four working days once material is on site. Removal of an old fence, tight alley access, or gate automation extends that, and we give you the schedule in the estimate so you can plan around it.
It depends on height, location, and whether the fence sits in a setback or near a property line. Anaheim issues permits through the city’s own building division, so we check your specific lot rather than guessing. If a permit is required, we pull it and see it through inspection.
Usually yes. Posts go into specific holes, not a continuous trench, so most of your yard stays intact. We mark the holes, protect the lawn with plywood where needed, and haul off the spoil. Landscape repair after digging isn’t included in the base price, and we tell you that upfront.
Expect $3,500 to $9,000 for a typical residential run. Footage, material grade, gate count, removal, and site access move the number. Call (888) 255-9354 for an exact quote; estimates are free.
Every install is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. If a gate settles or a fastener fails, we come back and make it right.
Get a Free Iron Fence Estimate in Anaheim
Call (888) 255-9354 for a free on-site estimate on your iron fence in Anaheim. A live person answers around the clock, every day, and can get a site visit scheduled. On the visit, we measure the run, check utility locations, confirm the property line, and hand you a written line-item quote with no surprises. You’ll also hear about our current $1,000 off projects over $10,000 and 0% financing for 18 months. We’re insured and bonded, and every job carries the 730-Day Done Right Promise.
Written by the team at Groundwork Construction Co.












