







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Anaheim, CA: What It Actually Takes
Metal roofing in Anaheim, CA runs $15,000 to $40,000 for a full residential install, and most homes take 4 to 7 working days from tear-off to final inspection. A standing seam system is the most common choice; exposed-fastener panels are the budget option. Either way, the roof is a specialty job, not the same crew and sequence as a shingle tear-off. Call (888) 255-9354 for a free estimate and we’ll walk your roofline, measure the actual square count and tell you what it costs before anything gets ordered.
How We Sequence a Metal Roof Install

Metal over an existing roof is a mistake. Every install starts with removal, and every stage below has a duration we hold to.
Stage 1: Tear-off and deck inspection (1 – 2 days)
We strip the old roof to the sheathing, then walk the deck board by board. On Anaheim’s older frames, that’s where soft spots and old underlayment show up. You get photos and a written line-item for any decking replacement before we proceed. No surprise line on the invoice at the end.
Stage 2: Structural check and deck prep (half a day to 1 day)
Metal is lighter than tile but the attachment points are different, so we verify the sheathing, add blocking where the panels fasten and confirm the fascia can carry the drip edge. This is where we decide if you need a permit revision or just a fastening plan. You won’t be asked to make that call; we bring it to you plainly.
Stage 3: Underlayment and waterproofing (1 day)
Our high-temp synthetic underlayment goes down over the clean deck, plus ice-and-water membrane at the valleys and penetrations. Anaheim’s long dry summers and flash thunderstorms mean the underlayment is the backup layer that matters most in the 10 years before anyone looks at the roof again.
Stage 4: Panel install (2 – 3 days)
Standing seam panels go down in runs, with concealed clips that let the metal expand and contract through Anaheim’s hot days and cool nights. Exposed-fastener panels go faster, but every screw is a future leak point. This is the stage you’ll see the most progress. You pick your finish color here if you haven’t already.
Stage 5: Final inspection and walk-through (same day as completion)
We close out the permit with the city, run a hose test at the penetrations and walk the roofline with you. You get the paperwork, the warranty in writing and our 730-Day Done Right Promise behind the workmanship. If it’s not right, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Most Anaheim homeowners land on one of these three systems. Here’s the honest trade-off on each.
- Standing seam metal (concealed fasteners): The premium choice. Panels run in long lengths with no screws through the face, so it holds up best against wind-driven rain and the Santa Ana wind events coming off the canyons. Color is part of the metal, not a coating. Suits owners staying in the home long-term.
- Exposed-fastener panels (screw-down): The budget option at the lower end of the range. Faster to install, fine on sheds, garages and simple gable profiles, but the washer on every screw is a wear point. Suits cost-focused projects and outbuildings more than a primary residence.
- Stone-coated steel (tile-look): For Anaheim homes that want the tile silhouette but not the weight. Common on Spanish-style and Mediterranean profiles. The trade-off is a higher per-square cost and a finish that can dull in full sun over time. Often paired with Impact Windows & Doors in Anaheim when a homeowner is doing the full exterior envelope at once.
On finish: matte and low-gloss colors hide the panel seams and dust in Anaheim’s dry seasons. Gloss shows every fingerprint and every smudge from the install. We’ll bring samples to the estimate. James Hardie fiber-cement trim pairs cleanly with metal panels at the fascia, and we can fold that into the same scope if you’re replacing trim while the roof is open.
What Metal Roofing Costs in Anaheim, CA

Plan on $15,000 to $40,000 for a full residential metal roof in Anaheim. Four variables push a project toward the low end vs the high end.
- Roof size and pitch: A compact single-story ranch at 1,500 sq ft lands near the low end. A two-story with dormers, valleys and steep pitch adds labor hours fast and can double the square count in cuts and waste.
- Decking condition: Replacing 20% of the sheathing is different from replacing 80%. Old framing on Anaheim’s pre-war bungalows is where decking often fails the walk-through.
- System choice: Standing seam sits at the top of the range, exposed-fastener at the bottom. Upgrading to a premium stone-coated steel sits near the top.
- Penetrations and accessories: Skylights, multiple chimneys, complex valleys, gutter replacement and any structural repairs each add to the line-item.
What’s included: tear-off, disposal, permit, underlayment, panel system, standard flashings and final inspection. What typically isn’t: deck replacement beyond what’s visible, structural upgrades, gutter replacement, and skylight relocation. A written line-item quote separates these so there’s no gray area mid-project. No-hassle upfront pricing means the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Anaheim Homes Specifically Do to This Job
Anaheim’s housing stock splits this job in two. In the older grid near downtown, including 92805 and the Colony District, pre-war bungalows and Craftsman frames often hide soft or under-sized decking that adds a day to tear-off and a line-item to the deck repair. Those homes also fall under the city’s own building division for permitting rather than the county, so the submittal timeline runs through Anaheim’s counter. In Anaheim Hills (92807/92808), the slope changes everything: Santa Ana wind events out of the canyons mean panel attachment and uplift rating get real scrutiny, and brush-clearance and wildfire-hardening come up on nearly every hillside roof. Flatland subdivisions in 92806 don’t see those conversations at all. On all of them, we schedule installs to dodge peak summer heat, both for the material and for the crew working overhead. If your project runs into a broader scope, this is part of a full Roofing in Anaheim conversation that includes gutters, fascia and any structural repairs the walk-through turns up. We cover the whole city; see our Anaheim service area page for the ZIPs and neighborhoods we work.
Serving Anaheim, CA – Our Local Coverage Area
We serve Anaheim and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Anaheim

Most residential installs run 4 to 7 working days once the permit is in hand. Anaheim’s permitting window typically adds another 2 to 4 weeks before the crew can start. Simpler roofs on 92806 tract homes often finish closer to 4 days, and steep Anaheim Hills roofs run longer. Call (888) 255-9354 for a specific timeline on your roof.
Yes, a reroof permit through the City of Anaheim’s building division is standard, and metal installs get an inspection at deck prep and final. We pull the permit, coordinate the inspection and handle the closeout. You won’t be chasing the city. Call (888) 255-9354 to talk through the permit path for your property.
We don’t recommend it, and we won’t do it. Metal needs a clean deck for proper fastening and underlayment, and layering traps the old roof and hides deck problems. Tear-off adds one to two days but is the only way the system performs to its rating.
The range is $15,000 to $40,000, with the median residential install landing in the middle of that band. Size, deck condition, system choice and penetration count move the number most. Call (888) 255-9354 for an exact quote; estimates are free and itemized in writing.
Our workmanship is covered by the 730-Day Done Right Promise, and every panel system carries its manufacturer warranty on top. If it’s not done right, we make it right, in writing. Manufacturer terms vary by system, and we’ll walk you through the exact coverage on yours at the estimate.
Get a Free Metal Roofing Estimate in Anaheim
Call (888) 255-9354 to schedule a free, no-obligation on-site estimate for metal roofing in Anaheim. A live person answers 24/7, so you’re not leaving a message and waiting for a callback. We’ll measure the roof, inspect the deck, check the permit path with the city and hand you a written line-item quote with the exact system and color you pick. Background-checked, uniformed technicians on every visit, and 0% financing for 18 months is available. If you’re also updating windows while the roof is open, we handle Window Replacement in Anaheim in the same project window. Find the full scope of our Roofing work and see where metal roofing fits.
Written by the team at Groundwork Construction Co.












