







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Fence Installation: The Yorba Linda Owner’s Guide
Unilock fence installation in Yorba Linda typically runs $3,500 to $9,000 installed, depending on linear footage, wall and column configuration, and site grading. Most of the work is scheduled in a single visit once materials are on site, and we confirm a firm number before anyone digs.
Owners rarely spot a failing Unilock fence all at once. What usually happens: a column cap works loose after a Santa Ana wind event, water gets behind the block, and the first crack shows up eight or ten months later. The other common entry point is a wall panel that starts leaning a quarter inch after a wet winter because the base course was never set on proper compacted aggregate. By the time a Yorba Linda homeowner calls us, the failing section is obvious, but the cause has been quietly at work for a season or two. We look at the whole run, not just the broken piece.
Which Unilock Models This Applies To

Unilock’s fence and wall systems are modular, and the block profiles have changed across production runs. The two lines we install most often in Yorba Linda are the Brussel Block and the Rivenstone wall systems, along with the pillar and cap configurations that go with them. Each has its own nominal block dimensions, and the differences matter when you’re replacing a few units instead of the whole run. A cap that looks identical in a photo can be half an inch off in depth, which shows once it’s mortared in place.
The reliable way to identify the right block is to measure, not eyeball. Note the block’s face width, height, and depth to the nearest eighth inch, then check the inside face of a removed unit for a mold stamp. Unilock does not print a model number on every block, so measurement is often the only path.
On the OEM-versus-aftermarket question: Unilock block is proprietary, and there is no true aftermarket equivalent for the colored and textured units. Generic CMU or big-box retaining wall block will not color-match or dimension-match, and mixing them into a visible run is a mistake every time. Where aftermarket is legitimate: base aggregate, rebar, drainage gravel, and adhesive. Those are commodities, and good ones perform identically to the branded version. Groundwork Construction Co. of Yorba Linda is an independent service provider, not affiliated with Unilock, so we source genuine material through authorized channels and tell you exactly where it came from.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Fence Installation Is Failing
- Leaning panels or a bowing run. Usually a base-course failure – the aggregate under the first course was not compacted to depth, and Yorba Linda’s clay-heavy soils in the hillier tracts move with seasonal moisture. A wall that leans within two years of installation is almost always a base problem, not a block problem.
- Loose or shifted column caps. Cap adhesive breaks down when water gets behind the cap and freezes or expands. Once a cap lifts, the column core is exposed to rain and the failure accelerates fast.
- Efflorescence that keeps returning. White mineral bloom on the block face is normal once. Coming back season after season means water is migrating through the wall rather than draining away from it, often because the drainage plane was never installed.
- Visible cracks running through block units, not just mortar joints. Cracks in the joint are cosmetic. Cracks through the block itself point to settlement or a missing geogrid layer, which is a structural issue, not a patching job.
- Soil pulling away from the base on the back side. This is the quiet one. Backfill that has settled or washed out leaves the wall unsupported, and it will show up as a lean within one or two wet seasons.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Unilock fence installation in Yorba Linda runs $3,500 to $9,000 installed. What moves the number: linear footage, wall height, number of columns and caps, gate integration, and whether the existing footing needs replacement or can be reused. A short decorative run sits near the bottom of that range; a full property-line wall with multiple pillars and a gate lands near the top.
We quote parts and labor as separate line items so you can see what the Unilock material actually costs versus the install. Base prep, compaction, drainage, and mortar are itemized, not bundled into a single number. Every job is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right. Pricing is upfront, and the number you see is the number you pay. No change-order surprises once the trench is open.
DIY or Call Us?
You can safely check a few things yourself: measure the block units, photograph the failing section from a few angles, and note whether the lean is in the panel or the column. That information helps us quote accurately over the phone.
Where DIY goes wrong is base prep and block matching. A homeowner can set a few blocks in a straight line, but a Unilock wall is only as good as the compacted aggregate and drainage beneath it, and getting that wrong means redoing the entire run in two years. Color-matching a partial repair is also harder than it looks – the production batch matters, and a mismatched unit in a visible wall is permanent. On any wall over about three feet, and on anything close to a property line, we recommend a trained crew. The inspection and permit side alone is worth the call.
Call (888) 255-9354 and we’ll walk through what you’re seeing, confirm the likely cause, and set up a free estimate.
FAQs

How long does a Unilock fence last in Yorba Linda?
A properly installed Unilock wall system should last 25 to 40 years in Southern California’s climate – the block itself is rated for decades, and the failure point is almost always the base or the cap adhesive, not the material. The main local threats are seasonal soil movement on sloped lots and UV breakdown of cap adhesive, both of which are preventable with correct installation.
Can a failing Unilock fence be repaired instead of replaced?
Yes, in most cases. A section repair – replacing loose caps, re-setting a leaning panel, or rebuilding one column – is usually possible if the base course is still sound. We assess the base first. If the base has failed, a partial repair just delays a full rebuild.
How long does the replacement take?
Most Unilock fence repairs and small installs are completed in a single visit, typically a full day for a standard run. Larger walls with multiple columns or a gate can run two to three days, depending on site access and curing time.
How do you source the Unilock material?
We source genuine Unilock block and caps through authorized supply channels and confirm the batch and profile before ordering. Because Unilock is proprietary, there is no reliable aftermarket substitute for the visible block, so we don’t use one. We’ll show you the material spec before we order.
We also work with KraftMaid, Cambria, and Silestone on the interior side of the house, along with the full range of exterior trades. One contractor, foundation to finish line.
Call Groundwork Construction Co. of Yorba Linda at (888) 255-9354 for a free estimate. Calls are answered by a live person 24/7, and every job is backed by the 730-Day Done Right Promise. Upfront pricing, 0% financing for 18 months, and $1,000 off projects over $10,000 – so the number you agree to is the number you pay.
Written by the team at Groundwork Construction Co. of Yorba Linda, serving Yorba Linda and nearby areas.












