







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
IKO Bathroom Remodeling: The Yorba Linda Owner’s Guide
Bathroom remodeling with IKO products in Yorba Linda typically runs $9,000 – $28,000 installed, and we schedule a free on-site measure so you know within days, not weeks, exactly what your project requires. That range covers IKO waterproofing membrane, shower systems, and tile backer assemblies installed by technicians with up to 12 years of experience, backed by our 730-Day Done Right Promise. Smaller powder rooms and tub-only scopes fall in the $5,000 – $12,000 band. Every quote is line-item and upfront, with no change orders waiting to surprise you.
Yorba Linda owners usually find the failure the same way. A shower pan starts weeping into the ceiling below. Membrane behind the tile bubbles or the grout line stays dark no matter how often you scrub. Maybe a slow leak shows up at the base of the wall after a winter of Santa Ana wind-driven rain pushing against the exterior. IKO waterproofing and shower systems are a strong product line, but they only perform as well as the substrate and slope they sit on. When one of those gives, the fix is a rebuild, not a patch.
Groundwork Construction Co. of Yorba Linda is an independent service provider. We’re not affiliated with IKO.
Key Takeaways
- IKO bathroom projects in Yorba Linda: $9,000 – $28,000 installed; small baths $5,000 – $12,000.
- Waterproofing fails from bad slope and movement, not from the membrane itself going bad.
- Every job is covered by our 730-Day Done Right Promise.
- Upfront pricing, 0% financing for 18 months, and $1,000 off projects over $10,000.
- Call (888) 255-9354 to schedule your free estimate and design consult.
Which IKO Models This Applies To

IKO’s bathroom and waterproofing line is narrower than the roofing products most people know them for, so matching the right material matters. Their key products for wet areas include IKO AquaBarrier waterproofing membrane, IKO Shower-Pro boards and panels, and their cement backer assemblies. Each one has a compatibility list. AquaBarrier bonds to specific thin-set mortars; use the wrong adhesive and the bond fails before the tile ever goes up.
Identify your product two ways. First, check the label or printing on the board edge or membrane roll for the IKO series name and lot number. Second, measure the panel thickness and sheet width: shower boards commonly run from 1/2-inch to 1/2-inch-plus depending on the panel, and a mismatch against your existing framing changes the whole assembly. If the label is gone, a moisture meter and a look at the substrate tell us what’s underneath and what replacement board will actually sit flush.
The OEM-versus-aftermarket call: for a full rebuild we specify IKO-compatible systems we can warranty end to end. For a repair where the existing IKO membrane and backer are still sound, a compatible aftermarket membrane or board from a tested line does the job and often saves money. We tell you which path your project needs after we open the wall, not before. We don’t carry parts on a truck and we don’t stock product locally. We source to your scope.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your IKO Bathroom Remodeling Is Failing
The waterproofing assembly is working until it isn’t, and the symptoms show up in predictable order:
- Water staining on the ceiling below the shower. This points to a failed pan liner or a membrane seam that never bonded. Water finds the seam first because that’s the weakest joint in any wet-area assembly.
- Soft or spongy spots in the shower floor or surrounding subfloor. A shower pan that flexes means the mortar bed or backer broke down. IKO systems hold up for decades set on a solid, sloped base, and they fail fast on one that isn’t.
- Loose tile or hollow-sounding spots behind the wall. The thinset lost its grip on the substrate. That usually traces to a backer that wasn’t fastened tight or a below-spec mortar, not the tile itself.
- Persistent mildew at grout lines and caulk joints. Grout that stays dark after cleaning means moisture is trapped behind it. The membrane or the seal at the pan is letting water in where it shouldn’t go.
- Efflorescence (white chalky mineral deposits) on tile or grout. Water is migrating through the assembly and drying on the surface, leaving the minerals behind. In Yorba Linda’s hard water, this one shows up faster than it does in softer-water areas.
Any two of those together mean it’s time for a real look at the assembly, not another coat of sealer.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Bathroom remodeling in Yorba Linda with IKO materials lands in these installed ranges. Every price is the number installed, not a parts-only figure with labor bolted on later.
- Full bathroom remodel: $9,000 – $28,000
- Small bathroom remodel: $5,000 – $12,000
- Walk-in shower installation: $4,500 – $12,000
- Tub-to-shower conversion: $3,500 – $10,000
- Shower replacement: $3,000 – $8,500
- Bathroom vanity installation: $800 – $3,000
What moves the range: whether we rebuild the subfloor and framing, whether plumbing is relocated, your tile selection, and how much drywall comes down to reach the failing membrane. On a full remodel, the waterproofing assembly is a smaller line on the quote than most owners assume. The bulk is tile, fixtures, and demolition. Our price is fixed once we’ve seen the room. From foundation to finish line, one contractor handles the whole scope, and the 730-Day Done Right Promise covers the install in writing. Call (888) 255-9354 for an exact number; estimates and design consults are free.
DIY or Call Us?
Some of this you can check yourself. Press on the shower floor for flex. Look for efflorescence and dark grout lines. Run the shower for ten minutes and watch the ceiling below for staining. Those are safe, useful diagnostics.
What we don’t recommend you take on: tearing out the existing membrane and rebuilding a shower pan. That’s genuine, injury-level risky work. A failed pan grind or a sheet of backer board loaded with tile can cut or crush. Plumbing is live, and a botched slope means water damage into your framing within months. That’s the work a trained crew with the right tools should handle. And on any project this size, building-permit scope in Yorba Linda depends on the jobs. If you’re planning a shower remodel in Yorba Linda with plumbing changes, plan on a permit.
We pull the permits and pass the inspections as part of the job. We also install KraftMaid vanities, Cambria and Silestone counters alongside the IKO waterproofing, so the whole room comes together under one contract. Background-checked, uniformed technicians on every visit. Call (888) 255-9354 and a live person answers, day or night.
FAQs

How long does an IKO waterproofing assembly last in Yorba Linda? A properly installed IKO wet-area system on a sloped, solid base commonly holds for 25 to 30 years or more before the assembly needs a rebuild. The membrane itself is rarely the first thing to go; the substrate underneath is. Two things shorten the life here: the region’s hard water, which wears joints and grout faster than soft water, and shower pans that were never recessed to a proper slope. Call (888) 255-9354 to have us look at what’s under your tile.
Can the failing part be repaired instead of replaced? Sometimes, yes. If one seam of the membrane shows a bond failure and the rest of the pan and backer are sound, a targeted repair can extend the life of the assembly. If the pan flexes or water is reaching the framing, a repair is money thrown at the symptom. We tell you which one it is after we open the wall. Call (888) 255-9354 for the assessment; estimates are free.
How long does a shower swap take? A shower replacement runs three to five working days once materials are on site. A full bathroom remodel in Yorba Linda with plumbing and layout changes runs two to four weeks. Any project that needs a permit adds the review time on the front end, and we factor that into the schedule before we start. Call (888) 255-9354 to get a real timeline for your room.
How do you source the IKO part? We match the exact model off the label or by measuring the panel and membrane, then source to your inspected scope, whether that’s an IKO-branded system or a compatible alternative we can stand behind. We don’t claim local stock and we don’t guess. Call (888) 255-9354 and our team will walk you through what your project actually needs.
Written by the team at Groundwork Construction Co. of Yorba Linda, serving Yorba Linda and nearby areas.












