







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Yorba Linda Owner’s Guide
If your Schluter driveway and paver system has a failed component, we replace it with Schluter-compatible parts and reinstall to spec. Typical installed pricing in Yorba Linda runs from $7,000 to $18,000 for a full paver driveway, with individual repairs and component swaps priced much lower depending on scope. Call (888) 255-9354 and we’ll give you an upfront number with no surprises.
Most Yorba Linda owners find out something’s wrong the same way: a paver lifts at the edge near the garage apron, grout or joint sand washes out after a rain, or the drainage profile at the driveway crown stops shedding water toward the street. Schluter’s system is built around a sloped substrate and edge restraint, so when water sits instead of running, that’s usually the first visible symptom.
Key Takeaways
- Schluter paver and driveway components are matched to substrate and edge-restraint spec, not universal.
- Our technicians have up to 12 years of experience with paver systems and Schluter-compatible installs.
- We’re an independent service provider, not affiliated with Schluter.
- The 730-Day Done Right Promise covers every install we do: if it’s not done right, we make it right.
Which Schluter Models This Applies To

Schluter’s driveway and paver line covers edge-restraint profiles, drainage channels, and substrate transition components, and each one is spec’d to a specific paver thickness and load class. A residential driveway in Yorba Linda carries passenger vehicles and the occasional delivery truck, so the profile you need is keyed to the load and the paver depth, not just the brand. The first thing we confirm on any repair call is the profile series and the measured paver thickness, because a part that’s a millimeter off in height will telegraph through the surface within a season.
Identifying the right part starts at the label or stamped marking on the existing profile, then a physical measurement of the channel or edge height. If the label’s gone, we measure the installed height, the paver depth, and the reveal at the joint. That’s where OEM vs. aftermarket matters for Schluter specifically: their profile geometry is proprietary, so a generic edge restraint that “fits close” typically won’t seat the same way, and you’ll get movement or water infiltration at the joint. We source genuine Schluter-compatible components for the visible, load-bearing parts and only use equivalents where the spec allows it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Driveway & Pavers Is Failing
- Pavers lifting or rocking at the edge. The edge restraint has lost its anchor or the substrate under it has settled, so the profile no longer holds the paver field in compression.
- Joint sand or grout washing out after rain. Water is getting under the surface instead of running to the drainage profile, usually because a channel is clogged or the slope has shifted.
- Standing water at the driveway crown or apron. The low point has moved, which means the substrate settled and the profile’s drainage plane is no longer pitched correctly.
- Cracks or separation at the transition to the garage slab or street. Expansion and transition components have failed, and Yorba Linda’s summer heat cycling speeds that up on south-facing driveways.
- Visible rust or corrosion on metal edge profiles. Inland Orange County’s dry summers and occasional marine moisture push metal profiles to fail faster than a coastal install would, especially where irrigation overspray hits the edge.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing in Yorba Linda depends on how much of the system failed and whether we’re replacing one component or rebuilding a section. Here’s how the numbers break down:
- Component or edge-profile swap (partial section): priced per the scope, quoted upfront before work starts.
- Paver driveway installation (full): $7,000 – $18,000.
- Paver patio installation: $3,500 – $11,000.
- Driveway replacement (full): $5,000 – $14,000.
- Driveway sealing (after repair): $250 – $700.
What drives the range: the total square footage, whether the substrate needs correction, the paver thickness and profile spec, and how much transition or drainage work is involved. Every quote is line-item and upfront; the number you see is the number you pay. All work is covered by the 730-Day Done Right Promise, so if a profile fails or water pools where it shouldn’t, we make it right.
DIY or Call Us?
You can safely check a few things yourself. Look for standing water after a hose test, note where pavers rock when you step on them, and check the edge profile for rust or a gap where it should sit tight. Photograph the label or stamped marking if you can see it, and measure paver thickness and profile height; that’s genuinely useful information to bring to a call.
Where DIY goes wrong is the reinstall. Edge restraint and drainage profiles have to be set to the correct height and pitch, and a paver field has to be re-compacted in the right sequence; get it wrong and the surface fails again within a season. This is also load-bearing work under vehicles, so an improperly seated profile can shift and become a trip or settling hazard. We hand this to trained technicians for a reason. Our technicians have up to 12 years of experience, are background-checked and arrive in uniform. Call (888) 255-9354 to schedule your free estimate.
FAQs

A properly installed profile and paver system should hold for many years, but inland Orange County heat cycling and irrigation overspray shorten the life of metal profiles compared to coastal installs. When a component fails early, it’s usually a spec mismatch or substrate issue, not normal wear. Call (888) 255-9354 for an exact quote on your repair; estimates are free.
Sometimes yes. If the failure is isolated to one edge profile, a transition piece, or a drainage section, we can often swap just that component and re-seat the surrounding pavers. If the substrate has settled under a larger area, a partial rebuild is the honest fix. We’ll tell you which one you’re looking at before any work starts.
A single component swap typically finishes in a single visit, while a partial rebuild with substrate correction takes longer depending on square footage and curing time between steps. We give you a real timeline with your written quote, not a guess.
We confirm the profile series and measured spec first, then source the genuine Schluter-compatible component that matches it. For paver systems, that spec match is what keeps the surface from telegraphing or shifting down the line. All work is backed by the 730-Day Done Right Promise. Call (888) 255-9354 to schedule your free estimate.
We also work with KraftMaid, Cambria, and Silestone on the interior side of the same homes; if your project spans more than the driveway, we handle it from foundation to finish line. Finals financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off. Live person answers every call, 24/7.
Call (888) 255-9354 for a free estimate on your Yorba Linda Schluter driveway and paver repair, or to schedule a design consult for a full replacement.
Written by the team at Groundwork Construction Co. of Yorba Linda, serving Yorba Linda and nearby areas.












